, , , ,

Hikvision DS-KH8300-T Video Intercom Indoor Station with 7-inch Touch Screen

7 inch Touch-Screen Indoor Station, Colorful TFT LCD display resolution: 1024 * 600, 10/100Mbps Ethernet; 8-ch alarm input,support SD card, 12 VDC/24 VDC, Power Over Network Cable (DS-KAD606-P_optional)

$257.00 $350.00 inc GST +3 Year Warranty & Support


Intercom (11)

Hikvision Australia’s website has firmware updates for available IP cameras.

Use the search bar to try and find your product. Firmware updates are usually available on the product page.


You will need to contact us if you can’t find your camera listed or if you require firmware for your NVR / DVR.
You will need to also provide the full serial number of the device as well as your current firmware.
This is to ensure upgrades are done properly. In some instances middlle firmware is required before upgrading to the latest version.

We do not recommend doing intercom firmware upgrades. Please check with us if there is any doubt.

If you didn’t buy equipment from us, please contact the people who you bought the equipment from.

This is a tech note providing guidance for setting up Hikvision IP Intercoms.

Cabling requirements:

> ethernet cable from every Door Station to Poe Switch
> ethernet cable from every indoor Monitor to Poe Switch
> ethernet cable from Poe Switch to the modem (if you wish to set up remote communication)

Need to unlock a gate? 

If you need to open/ control 1-2 door / gate strikes, run 4 core cabling from the Intercom Door Station to the respective strikes. These strikes need to be powered separately, ie. the door station will not be able to power these strikes.

GEN 2 Guides

Indoor Station Configuration Guide
Indoor Station Operation Guide
Indoor Station Quick Start Guide

How to setup – guide from Pipl Systems – https://pipl.systems/setup-tutorial-hikvision-2nd-modular-intercom-system/

Add a second monitor – https://www.youtube.com/watch?v=-11RJ1S-8Xg

GEN 1 Guides

Please click to download.

How to set up HIKVISION intercom for first time

How to configure a Hikvision Villa Intercom System


Hikvision Intercom add to Hik Connect

This tech guide from Hikvision helps you configure a Hikvision apartment intercom system.



SADP stands for search active device protocol, it’s Hikvision’s free and simple utility for searching Hikvision products (including IP cameras and DVRs/NVRs) in the local network.

Its commonly used for:

  • resetting password
  • Finding out what firmware is currently used
  • changing IP addresses

SADP TOOL – https://www.hikvision.com/en/support/tools/destop-tools/sadp-for-windows/

Below is a great article which delves into the SADP tool in greater detail.



Hikvision CCTV cameras can be added to an indoor station thus allowing remote viewing directly from the indoor station for added security.
A typical Hikvision room station can have up to 16 cameras viewable.

For a guide as to how to set this up, please see attached:


NOTE these instructions are for Gen1 intercoms only.

These tech notes should assist you with this requirement.



In an Intercom system with 2 or more indoor stations, each station can dial or call between each other by using the following dialing format.

0- (Main indoor unit is typically 0 and other extension units are 1 thru 5)
For Example:

To call the Main indoor station from any indoor station you would dial 0-0

To call the first indoor extension from any indoor station, included the main indoor station, you would dial 0-1

Please refer to page 8 of the user manual.

Most residential customers would use the Green and Blue cable
The Power would depend on the electric strike (to be powered separately). Further, the strike also has NO and NC setting. So, the strike has to also be on NO setting
For commerical sites, some of them may use NC, so in that case, we still use electric strike but use the pink, NC cable to connect to it

It is possible to add cameras to the HIkvision IP intercom system. Follow the steps below:


Most common system – 1 door station – 1 monitor:

1. Follow the setup via the indoor monitor. No need to even load IVMS4200.
2 Scan the QR code via Hik Connect app to setup remote viewing

System with 1 door station, 1 main room and multiple sub room stations

1.Set up the first unit using the main room monitor
2. Add the subroom monitors using IVMS4200. (the IP addresses are examples only)

Apartment system

Configure as above with IVMS4200. IP addresses are samples

System with multiple door stations

Configure as above with IVMS4200. IP addresses are samples

Some helpful hints

HIK CONNECT Only Master room stations should be added to Hik-Connect. Issues may occur if a Sub station is added. The app can be found on the iOS and Android app stores.

Load More

You may also like…

Save & Share Cart
Your Shopping Cart will be saved and you'll be given a link. You, or anyone with the link, can use it to retrieve your Cart at any time.
Back Save & Share Cart
Your Shopping Cart will be saved with Product pictures and information, and Cart Totals. Then send it to yourself, or a friend, with a link to retrieve it at any time.
Your cart email sent successfully :)