Product SKU: T91D62
Product Overview
Rooftop and elevated facade installations regularly present parapets that are too deep, too irregular, or too obstructed for a standard fixed-length wall bracket to clear. The AXIS T91D62 Telescopic Parapet Mount addresses this directly with an arm that collapses to 783mm and extends to 1033mm across an overall mount width of 1007mm, providing approximately 250mm of working range to accommodate varying parapet depths and architectural features. Featuring a 180-degree swivel on its own axis, the T91D62 allows camera alignment and maintenance to be performed from the rooftop surface rather than from below. Rated IK10 and NEMA 4X, the corrosion-protected aluminium body is suited to exposed commercial and industrial environments including coastal sites. It accepts a 1.5-inch NPS thread and carries a 10kg maximum load capacity, supporting both outdoor fixed dome and PTZ dome cameras from the AXIS range. An optional retrofit bracket also enables reuse of existing Pelco PTZ dome parapet mount drill holes on upgrade projects.
Key Capabilities
Telescopic Adjustable Arm
The arm collapses to 783mm and extends to 1033mm, delivering approximately 250mm of adjustable reach. This allows installers to clear parapets of different depths and work around facade obstructions without fabricating custom brackets or stacking adapters on site.
180-Degree Swivel on Own Axis
The mount rotates a full 180 degrees, enabling camera alignment and periodic servicing from the rooftop surface. On multi-storey commercial buildings where working over a parapet edge is impractical, this swivel function is a genuine safety and access advantage for installers and maintenance personnel.
IK10 and NEMA 4X Ratings
IK10 impact resistance and NEMA 4X certification confirm protection against windblown dust, rain, and physical interference. These ratings make the T91D62 appropriate for exposed rooftop positions and industrial wall locations where environmental stress is a constant factor.
Corrosion-Protected Aluminium Body
The aluminium construction is treated for corrosion protection, extending serviceable life in coastal, high-humidity, and industrial settings where untreated hardware deteriorates and requires replacement within a few years of continuous outdoor exposure.
10kg Maximum Load Capacity
A confirmed 10kg load rating supports the full weight of AXIS outdoor fixed dome and PTZ dome cameras, including heavier motorised models. At extended arm length, adequate load capacity is critical to maintaining structural rigidity and minimising vibration under wind load.
Best For
- Rooftop Parapet Coverage: The telescopic arm and 180-degree swivel allow cameras to be lifted clear of thick or uneven parapets, giving outdoor dome cameras an unobstructed sightline over perimeter edges, car parks, and access points below.
- Extended Wall Projection: Where building facades include cladding, cornices, conduit runs, or structural ribs that block a flush-mounted camera, the T91D62 projects the camera further from the wall surface to restore a clear field of view.
- Pelco-to-AXIS Upgrade Projects: The optional retrofit bracket enables reuse of drill holes originally made for Pelco PTZ dome parapet mounts, reducing penetration work and surface remediation costs on existing commercial and institutional buildings.
Why Choose the AXIS T91D62
The T91D62 is engineered for the specific problem of variable parapet depth, a challenge that a fixed-length wall mount or standard arm bracket cannot reliably solve. The 783mm to 1033mm adjustable range gives installers a genuine working window rather than a single fixed projection distance, avoiding on-site improvisation with stacked adapters or custom fabrication. The 180-degree swivel is not a convenience feature but a practical requirement on elevated rooftop installations where the installer cannot safely access the camera from below the parapet. The IK10 and NEMA 4X ratings are confirmed to the product specification, making this mount appropriate for Australian coastal and industrial outdoor environments. At 5.9kg, the mount itself is manageable for a single installer on a rooftop, and the 10kg load capacity covers the full range of compatible AXIS outdoor dome and PTZ dome cameras. Available at Security Wholesalers, the AXIS T91D62 is a purpose-built solution for professional installers who need adjustable elevated reach with documented outdoor performance ratings.
Buyer Decision Tips
Measure parapet depth and required camera clearance before ordering: The T91D62 arm adjusts between 783mm and 1033mm collapsed-to-extended. Before installation, confirm the parapet depth and the minimum clearance height needed to position the dome camera fully above the parapet edge. Also verify that the camera being mounted uses a 1.5-inch NPS thread, as this is the only thread size the T91D62 accepts. If you are upgrading from a Pelco PTZ dome parapet mount, the optional retrofit bracket is a separate item and must be ordered alongside the T91D62 if you intend to reuse existing drill holes.
Key Features & Technical Specifications
| Product Name |
AXIS T91D62 Telescopic Parapet Mount |
| Part Number |
AXIS-5507-271 |
| Mount Type |
Telescopic parapet mount and wall mount |
| Compatible Camera Types |
Outdoor fixed dome and PTZ dome cameras |
| Thread Size |
1.5 inch NPS |
| Collapsed Arm Dimensions |
1007 x 783mm |
| Extended Arm Dimensions |
1007 x 1033mm |
| Adjustable Arm Range |
Approximately 250mm of extension travel |
| Maximum Load |
10kg |
| Mount Weight |
5.9kg |
| Swivel Range |
180 degrees on own axis |
| Impact Rating |
IK10 |
| Weather Rating |
NEMA 4X |
| Material |
Aluminium with corrosion protection treatment |
| Installation Options |
Parapet mounting and wall mounting |
| Retrofit Compatibility |
Optional retrofit bracket available for reuse of Pelco PTZ dome parapet mount drill holes |
Ideal Use Cases
Commercial Rooftop Perimeters
Office towers, shopping centres, and warehouses with parapet walls use the T91D62’s telescopic arm to clear parapets of varying depth, positioning outdoor dome cameras above the edge for a full sightline across car parks, access roads, and building entries below.
Industrial Facility Walls
Factories and distribution centres with cluttered external walls benefit from the T91D62’s wall mount mode, projecting cameras beyond pipework, conduit, or structural ribs that would obstruct a flush-mounted dome’s field of view at loading docks and yard perimeters.
PTZ Dome Rooftop Deployments
The confirmed 10kg maximum load and 1.5-inch NPS thread accommodate heavier AXIS outdoor PTZ dome cameras on exposed rooftop positions, with the IK10 and NEMA 4X ratings providing structural and weatherproof confidence at height.
Camera System Upgrade Projects
Sites upgrading from Pelco PTZ dome parapet-mounted cameras can use the optional retrofit bracket with the T91D62 to reuse existing penetrations, avoiding core drilling and surface patching on finished concrete or masonry parapet structures.
Choosing the Right Model
- Choose this model if: You are mounting an outdoor fixed or PTZ dome camera on a rooftop parapet or a wall with obstructive facade elements, and you need an adjustable arm length, IK10 and NEMA 4X outdoor ratings, and a 180-degree swivel to manage camera alignment and servicing from the rooftop surface.
- Choose a different model if: Your camera position is at standard eave, soffit, or flat ground-floor wall height where the projection required is minimal. A compact fixed wall mount or ceiling mount will be lighter, lower profile, and more appropriate than a telescopic parapet arm sized and rated for elevated commercial outdoor applications.
FAQs
- What is the arm extension range on the T91D62, and how is it measured?
The arm adjusts from 783mm (collapsed) to 1033mm (fully extended), with the overall mount width fixed at 1007mm. This gives approximately 250mm of adjustable reach. The extension is measured along the projection axis, corresponding to how far the camera will sit from the parapet face or wall surface once the arm is set to the required length.
- Can the T91D62 be installed as a wall mount rather than a parapet mount?
Yes. The T91D62 supports both parapet and wall installation modes. When used as a wall mount, the telescopic arm extends the camera beyond flush-mounted positions, which is useful where external wall features such as cladding panels, conduit runs, structural ribs, or cornices would restrict a dome camera mounted directly to the surface.
- What thread size does the T91D62 require on the camera?
The T91D62 accepts a 1.5-inch NPS thread. This is a standard size across the AXIS range of outdoor fixed dome and PTZ dome cameras designed for parapet and extended-reach wall mounting. Confirm the thread specification of your specific camera model before ordering to ensure direct compatibility without adapters.
- Why does the 180-degree swivel matter on a rooftop installation?
On multi-storey buildings, accessing the street-facing or underside of a parapet to align a camera is often impractical without rigging equipment. The 180-degree swivel allows the installer to rotate and aim the camera from the rooftop surface during installation, and to reposition it during maintenance visits, removing the need for elevated access from below the parapet level.
- Is the T91D62 rated for coastal and industrial outdoor environments?
Yes. The aluminium body carries a corrosion protection treatment, and the mount is rated NEMA 4X, covering protection against windblown dust, rain, and splashing water. The IK10 impact rating adds resistance against physical interference. Together these make the T91D62 appropriate for coastal, port, and industrial sites where surface corrosion and environmental exposure are long-term concerns. The T91D62 is part of the Security Wholesalers range for professional AXIS installation projects across Australia.
- What is the optional retrofit bracket, and does it come included with the T91D62?
The retrofit bracket is a separate optional accessory that allows the T91D62 to be installed using drill holes originally made for Pelco PTZ dome parapet mounts. It is not included with the standard T91D62 and must be ordered separately. It is intended for upgrade projects where reusing existing parapet penetrations avoids the cost and remediation work of core drilling new holes in finished masonry or concrete structures.
Additional Information
