Product Overview
For installers deploying 2nd generation AXIS F Series modular cameras in concealed, embedded, or hard-to-reach locations, this 8 m sensor cable provides the physical link between a compatible AXIS F-series sensor unit and its main unit. Using an SMA male to FAKRA female connector configuration, the cable routes the RF signal reliably over its full 8 m length without signal degradation, with a rated frequency range of 0 to 3 GHz and 50 Ohm impedance. The SMA connector end carries an IP67 weathering rating, making it suitable for installations exposed to moisture and dust ingress. The cable also holds an IP66 rating and is approved to UN ECE R118, confirming its suitability for vehicle integration. It operates across an extreme temperature range of -40 degrees Celsius to 75 degrees Celsius, covering demanding indoor and outdoor deployments. Compatible main units include the AXIS F91 series, while supported sensor units include the AXIS F21, AXIS F41, and AXIS F72. The 8 m length suits installations where the sensor unit must be placed significantly further from the recorder or main unit than the standard 1 m variant allows.
Key Capabilities
8 m Sensor Extension Reach
The 8 m length allows sensor units to be positioned well away from the AXIS F91 main unit, giving installers flexibility to place cameras in concealed or structurally integrated positions that a shorter cable cannot reach.
IP67 Connector Rating
The SMA connector end is rated IP67, providing full protection against dust ingress and temporary water immersion. This makes the cable suitable for installations where connector joints may be exposed to outdoor conditions or high-moisture environments.
Extreme Temperature Tolerance
Rated for operation between -40 degrees Celsius and 75 degrees Celsius, this cable maintains integrity in harsh outdoor environments, cold-climate deployments, and vehicle installations where temperatures fluctuate significantly.
Stable RF Signal Transmission
With a 50 Ohm impedance and a frequency range up to 3 GHz, the cable maintains a consistent RF link between sensor and main unit across its full length, reducing signal loss risk in longer cable runs.
Best For
- Extended Sensor Placement: Installations where the AXIS F91 main unit cannot be positioned close to the sensor unit, such as ceiling voids, structural cavities, or separated compartments, benefit from the 8 m cable length.
- Vehicle and Transport Integration: The UN ECE R118 approval and wide operating temperature range make this cable a confirmed fit for in-vehicle F-series deployments such as fleet vehicles, buses, or rail carriages.
- Harsh or Outdoor-Adjacent Environments: The IP67 connector rating and condensing humidity tolerance of 10 to 100% RH support deployments in locations where moisture exposure at the connector joint is a practical risk.
Why Choose the Axis F Series Sensor Cable 02790-001
Where the standard 1 m sensor cable limits sensor unit placement to positions immediately adjacent to the AXIS F91 main unit, the 02790-001 opens up a full 8 m of routing distance. This is not a generic cable: it uses a specific SMA male to FAKRA female connector configuration engineered for 2nd generation AXIS F Series hardware, with confirmed compatibility across the AXIS F21, F41, and F72 sensor units. The IP67 connector rating, UN ECE R118 vehicle approval, and -40 to 75 degree Celsius operating range make it one of the few sensor extension cables suitable for both fixed architectural installations and in-vehicle applications without substitution. Installers who have worked with the AXIS F-series system understand that sensor placement flexibility is the core advantage of the modular design, and this cable preserves that advantage over longer distances. Available through Security Wholesalers, the 02790-001 is a purpose-built component for professionals who need a reliable, specification-matched extension for 2nd generation F-series deployments.
Buyer Decision Tips
Choosing Between the 1 m and 8 m Variants: If the AXIS F91 main unit can be located within 1 m of the sensor unit, the shorter cable reduces cable management complexity. The 8 m cable (02790-001) is the correct choice when routing through walls, ceilings, vehicle cavities, or any structural path that adds distance between the sensor and main unit. Only 2nd generation AXIS F Series main units and sensor units are compatible, so confirm your hardware generation before ordering.
Key Features & Technical Specifications
| Product Type |
Camera sensor cable (SMA male to FAKRA female) |
| Cable Length |
8 m (26 ft) |
| Connector Type |
SMA male to FAKRA female |
| Compatibility |
2nd generation AXIS F Series; AXIS F91 main units; AXIS F21, F41, and F72 sensor units |
| IP Rating |
IP66 / IP67 (SMA connector end) |
| Frequency Range |
0 to 3 GHz |
| Impedance |
50 Ohms |
| Bending Radius |
30 mm (1.2 in) |
| Operating Temperature |
-40 degrees Celsius to 75 degrees Celsius (-40 degrees Fahrenheit to 167 degrees Fahrenheit) |
| Humidity |
10 to 100% RH (condensing) |
| Outside Diameter |
3 mm |
| Weight |
124 g |
| Colour |
Black |
| Approvals |
UL CM E164469-F5, UN ECE R118 |
| Warranty |
3 years |
Ideal Use Cases
Ceiling Void and Cavity Installations
The 8 m cable length allows sensor units to be surface-mounted or pinhole-integrated in ceiling surfaces while the main unit sits out of sight in a ceiling void, keeping cabling concealed within the building structure.
Fleet and In-Vehicle Monitoring
UN ECE R118 approval and an operating range down to -40 degrees Celsius confirm this cable’s suitability for vehicle-mounted AXIS F Series deployments in buses, rail carriages, or fleet vehicles, where cabin temperatures fluctuate widely.
Covert Retail and Hospitality Surveillance
The modular AXIS F Series design is favoured for discreet sensor placement in retail fittings, counters, or hospitality environments. The 8 m cable allows the recorder or main unit to be positioned in a back-of-house location while the sensor remains hidden at the monitoring point.
High-Moisture and Industrial Environments
With an IP67 connector rating and humidity tolerance up to 100% RH condensing, the cable suits food processing facilities, wash-down areas, or industrial sites where moisture at the cable connector would compromise an unrated alternative.
Choosing the Right Model
- Choose this model if: You are installing a 2nd generation AXIS F Series modular camera system and need to route the sensor unit more than 1 m from the AXIS F91 main unit, particularly through cavities, vehicles, or wet environments where the IP67 connector rating provides meaningful protection.
- Choose a different model if: Your sensor and main unit will be located within 1 m of each other and cable management simplicity is a priority, in which case the shorter 1 m variant of this cable is the more appropriate choice. This cable is not compatible with 1st generation AXIS F Series hardware.
FAQs
- Which AXIS F Series main units and sensor units is the 02790-001 compatible with?
The 02790-001 is confirmed compatible with 2nd generation AXIS F Series hardware. Supported main units include the AXIS F91 series. Supported sensor units include the AXIS F21, AXIS F41, and AXIS F72. It is not compatible with 1st generation AXIS F Series products, so confirming your hardware generation before ordering is important.
- What is the IP67 rating on this cable and what does it mean for installation?
The IP67 rating applies to the SMA connector end of the cable. IP67 means the connector is fully protected against dust ingress and can withstand temporary water immersion up to 1 m depth for 30 minutes. This makes the cable suitable for connector joints exposed to moisture during installation or in service, without requiring additional connector sealing in most applications.
- Is this cable suitable for use in vehicles?
Yes. The 02790-001 carries UN ECE R118 approval, which is a United Nations regulation specifically covering cable and wiring harness fire resistance for road vehicles. Combined with its -40 to 75 degree Celsius operating temperature range, it is a confirmed fit for in-vehicle AXIS F Series installations including buses, fleet vehicles, and rail applications.
- What is the minimum bending radius for routing this cable through tight spaces?
The confirmed minimum bending radius is 30 mm (1.2 in). When routing the cable through wall conduits, ceiling cavities, or vehicle panels, maintaining a bend radius no tighter than 30 mm protects the cable’s RF shielding and prevents long-term signal degradation at tight corners.
- Where can I purchase the Axis F Series Sensor Cable 02790-001 in Australia?
The 02790-001 is available through Security Wholesalers, supplied as a genuine Axis Communications accessory with a 3-year warranty. It is stocked as a single-unit 8 m cable, with the shorter 1 m variant listed separately for installations requiring a tighter cable run between sensor and main unit.
Additional Information
AXIS 02790-001 Datasheet
